Click To Call(656) 254-4152Click To Get A Free Estimate
Dark herringbone paver driveway with a family standing on it in front of a brick ranch house after a wash and sealing

Clean surfaces and freshly packed joints

Paver Cleaning and Joint Sand in Westchase, FL

Call (656) 254-4152 to have a local contractor wash your Westchase pavers and pack the joints with fresh sand.

  • Brings out deeper paver color
  • Fresh joint sand helps lock pavers in place
  • Gives weeds less room to grow
  • Makes the surface easier to keep clean
  • Free estimate, no obligation

Request a Free Estimate

Free, no obligation.

Step 1 of 2

Where are your pavers?

Please choose one.

Free EstimateNo obligation
Fast ReplyWithin 1 business day, usually much sooner
Typical Local Price$1.25 to $2.50 a sq ft to clean, sand and seal
Call Now(656) 254-4152

Can I get my Westchase pavers cleaned without a long wait?

Paver cleaning is available across Westchase, FL, and a local contractor replies within 1 business day, usually much sooner. Fresh joint sand is part of the job, and the estimate is free with no obligation. To start, call (656) 254-4152.

Cleaning lifts off algae, mildew and grime so pavers look brighter and grip better underfoot. New sand then goes between them, which holds them steady and leaves weeds less room. Rusty's notes that algae makes wet travertine and concrete far more slippery, so a wash is a safety step as well as a looks step. A side walk that turned green after one wet summer can look like part of the property again. When you request a free estimate, point out the roughest spots.

Call (656) 254-4152

Broom pushing sand into the joints between herringbone pavers, a pale cleaned area on one side and a dull gray area on the other

What is part of a paver cleaning job?

The work covers stain treatment, a controlled wash and new joint sand once the surface dries. Book it by itself, or treat it as the opening stage of a seal job. Shady paths in Westchase villages and ground near sprinkler heads take the longest. To line up a cleaning, call (656) 254-4152.

Stain treatment

A treatment matched to the problem goes on first, whether mold, algae, oil or rust. Rusty's lists each of them as part of prep.

Controlled wash

Rusty's uses a rotary surface cleaner in place of a single jet wand, which covers an area evenly. Unilock says any spray should stay at 30 degrees or lower so the joint material stays put.

Fresh joint sand

Once the pavers dry, sand is swept into every gap. Unilock says to sweep in new joint material wherever it is needed.

Sealer if you want it

Sealer goes on afterward, once everything is bone dry. The sealing guide explains what that adds.

What are the signs my pavers need cleaning?

Green or black film along shaded edges, rust marks near sprinkler heads, weeds in the joints, white patches on newer pavers and sand strewn across the drive after rain all point to a wash. Rusty's names black algae streaking, green mildew and mold as common on Florida driveways. Algae on a pool deck or front walk is also a slip risk. To have yours looked at, call (656) 254-4152.

Is cleaning enough, or should I seal my pavers too?

Cleaning restores how pavers look today, and a sealer coat decides how long that look holds. Skipping the coat costs less up front, but in Westchase's humidity algae and fading come back on their own schedule. Unilock says a sealed surface is easier to sweep and wash, though the coat has to be redone every few years. Want the protective coat too? Say so when you request a free estimate.

How often should Westchase pavers be cleaned?

Rusty's says most homeowners clean every 12 to 18 months, and heavily shaded or tree covered driveways may need it sooner. Around a pool, it suggests every 9 months under heavy canopy or near water. Sunny, open drives hold up longer. To set a schedule for your own lot, call (656) 254-4152.

Does more pressure clean pavers better?

No. Unilock warns that wrong pressure or nozzle settings can crack pavers, erode them and blow out the joint sand, and it says to keep the spray at 30 degrees or lower. Rusty's washes screens at under 500 PSI and saves true pressure washing for decks and concrete. Ask what nozzle and pressure the contractor plans to use when you request a free estimate.

Technique counts as much as the machine. A rotary surface cleaner held at one height leaves an even finish, and a treatment chosen for each stain does the hard work in place of force. To ask about methods now, call (656) 254-4152.

Algae

Why do Westchase pavers turn green or black?

Damp shade is the cause. Rusty's says Florida's humidity and shade bring black algae streaking, green mildew and mold. A Westchase paver company points to preserved wetlands, retention lakes, mature oaks and golf course irrigation, which keep low and shaded pavers wet. A wash removes the growth, and fresh sand and a sealer coat help slow its return. To check your lot, request a free estimate.

What is the white film on newer pavers?

A chalky white film on newer pavers is typically efflorescence, a powdery deposit of calcium salts. Unilock says it is cosmetic and tends to fade in 2 to 3 months, though it can take up to a year, and that it should be gone before sealing. Old sealer that has turned cloudy can look similar. Point out the patch when you call (656) 254-4152.

How long do pavers need to dry before sealing?

Unilock says pavers may be dry in a few hours in warm sun and about 24 hours in cooler, shaded spots. Rain pushes that out, which is why a wash and a seal often land on separate days. Ask how a rainy forecast would change the date when you request a free estimate.

Surfaces

Which paved areas at a Westchase home can be cleaned?

Every paved surface around a home can be washed: the driveway, the pool deck, the patio and the front walk. Each collects its own kind of grime, so the treatment and the method change. To start with yours, request a free estimate.

Driveways

Cleaning a driveway matters most where the wheels run, since tires, oil drips and open sun all land there.

Screened pool decks and lanais

Cleaning a pool deck means working around splash water, chlorine and bare feet, so the finish has to keep its grip when wet.

Patios beside a golf course or a lake

Backyards near a retention lake or a fairway stay damp longer. Cleaning a patio there starts with the greenest corners.

Front walks and entries

Cleaning a front walk is a small job, yet it is the first surface every guest steps on.

Common problems

What leaves Westchase pavers dirty?

Fading, lost joint sand, damp-shade growth, stains from oak and sprinkler water, and settled ground lead the list. A wash deals with several of them, and sealing or repairs address the rest. To learn which apply at your address, call (656) 254-4152.

1. Fading from year-round sun

Rusty's names constant UV as a main cause of fading on Tampa Bay pavers, and an open driveway with no shade loses its depth first. A wash reveals the color still there, and a coat afterward helps hold it.

2. Joint sand lost in summer downpours

Heavy summer rain saturates pavers and erodes the sand between them, Rusty's explains. With the joints low, pavers can shift and weeds move in, so new sand goes in before any sealer.

3. Green growth in damp, shaded spots

Rusty's says humidity supports mold, mildew and algae, especially on pool decks, shaded patios and poorly drained areas. A Westchase paver company adds that wetlands, retention lakes, oaks and golf course irrigation keep many lots damp.

4. Stains from oak tannin and sprinkler water

Rusty's lists live oak tannin stains and hard water irrigation deposits as common local problems, and it notes that irrigation can leave rust marks too. Each needs its own treatment before sealer goes down.

5. Sandy ground that settles

Florida's state soil, Myakka fine sand, is sand throughout, and Wikipedia says its water table can sit within 10 inches of the surface for one to five months. Ground like that can settle under pavers, and Unilock says sealer will not cure a base problem, so low spots get fixed first.

Pricing

What does paver cleaning cost in Westchase?

Published Tampa Bay figures for cleaning on its own are scarce, so the numbers here come from larger packages. Rusty's Pressure Wash and Seal lists a pool cage and deck wash at $325 to $600 or more, and it says most companies set a minimum charge of $500 to $1,000. Condition, rust, oil and algae all change the quote. For a price on your property, request a free estimate.

Planning to seal as well? Request one quote for the whole job. The range Rusty's publishes for the full clean, sand and seal is $1.25 to $2.50 per square foot, which puts a 600 square foot driveway near $750 to $1,500. For help weighing the two, call (656) 254-4152.

Want more detail? Read the sealing guide, browse the places served or go back to the home page to send a request.

JobPublished Tampa Bay figureWhat it covers
Small job minimum$500 to $1,000The minimum charge most companies set, so a small patio is priced by the job
Pool cage and deck wash$325 to $600 or moreThe screen enclosure plus the pool deck, as one package
Full clean, sand and seal$1.25 to $2.50 per sq ftWash, fresh joint sand and sealer together
600 sq ft driveway, full job$750 to $1,500The per foot range applied to a two car driveway

Figures come from Rusty's Pressure Wash and Seal, a company working in Pinellas, Hillsborough, Pasco and Manatee counties. The last row is simple math on its range, and your own quote may land elsewhere.

Get a Free Estimate

Wet paver pool deck beside a screen cage where a family is swimming, the kind of deck that stays damp most of the day
Why choose us

Why use a contractor who works near Westchase for paver cleaning?

A contractor who already works around Westchase knows what humidity, oak shade and sprinkler water leave behind. Set the quote beside the published figures on this page, then decide when you are ready. To begin, request a free estimate.

A contractor who works nearby

A company that covers Westchase already knows its villages, its lakes and its shady lots. The first visit starts from local knowledge, not guesses.

Free to ask

The look at your pavers and the written estimate cost nothing. If the number does not suit you, say no and nothing is owed.

Published prices to measure against

Tampa Bay paver companies post what they charge per square foot, and this site passes those figures along. A bid far outside them deserves a question about what it includes.

Your pace, your decision

Request the price in writing, then take as long as you need. The contractor standards page covers what to check before you sign.

Want a free estimate to clean your Westchase pavers?

Send the short form or phone in, and a contractor writes back inside 1 business day, often sooner.

Call (656) 254-4152

Free, no obligation

Homeowners talking with a contractor on a brick red paver driveway beside a lawn and a stucco single story house
Photos

What do cleaned pavers look like around Westchase?

Freshly sealed paver driveway on a Westchase property
Sealed paver pool deck on a Westchase property
Sealed paver patio behind the home on a Westchase property
Sealed paver walkway to a front door on a Westchase property
Close view of freshly sealed pavers on a Westchase property
Paver area with one cleaned half beside a dirty half on a Westchase property
Contractor cleaning pavers on a Westchase property
Contractor sealing or sanding pavers on a Westchase property
How it works

How does the paver cleaning process go, step by step?

Skip the sealer and the job finishes once the joints are full at step four. To set a date, call (656) 254-4152.

1. Walk it and measure

To price the cleaning job at your Westchase home, the contractor measures the area and marks dips, cracked pavers, old sealer and any spot where water collects.

2. Cover and treat

Plants and screen panels are covered and the sprinkler timer is switched off. Mold and algae treatment, oil stain removal and rust treatment go on wherever they are needed, as Rusty's lists.

3. Wash with care

A rotary surface cleaner covers the pavers evenly, the way Rusty's describes, and any hose or wand spray stays at 30 degrees or lower, per Unilock, so the joints keep their sand.

4. Dry and refill the joints

Unilock says pavers dry in a few hours in warm sun and need about a day in cool shade. Fresh sand is then swept into each gap, which Rusty's says cuts down on weeds and ants.

5. Seal and walk the job

If sealer is on the work order, it goes on dry pavers with a garden-style sprayer and a foam or short pile roller, as Unilock lists. The contractor then walks the area with you and names how long feet and tires should stay off.

Questions

Frequently Asked Questions

How much does it cost to get pavers cleaned?

Published Tampa Bay figures mostly cover bigger packages. Rusty's Pressure Wash and Seal lists a pool cage and deck wash at $325 to $600 or more and says most companies set a $500 to $1,000 minimum. The full clean, sand and seal runs $1.25 to $2.50 per square foot, which puts a 600 square foot Westchase driveway near $750 to $1,500.

Can I pressure wash patio pavers?

Yes, with care. Unilock says to hold the spray at an angle no greater than 30 degrees, because a steep angle washes out joint material, and it warns that wrong pressure or nozzle settings can crack pavers or blow out sand. A Tampa Bay company says it uses a rotary surface cleaner in place of a single jet wand.

Is there a downside to sealing pavers?

The downside is upkeep. A sealed surface is a repeat job every few years, and gloss finishes can feel slick when wet, Unilock notes. Cleaning alone costs less up front but offers no protection, so algae and fading return on their own schedule.

How often should I seal pavers in Florida?

Plan on every three to five years, a span both Unilock and Rusty's give, with a wash about every 12 to 18 months in between, Rusty's says. Shaded or tree covered driveways in Westchase may need washing sooner. The wash keeps the sealer clean, and the sealer makes the next wash easier.

What are the orange or brown stains on my Westchase pavers?

Usually water or leaves. Rusty's lists live oak tannin and hard water irrigation deposits as common local stains, and says irrigation and patio furniture can leave rust marks. Each stain needs its own treatment, and all of them have to come out before sealer goes on.

Is it safe to clean a pool deck beside the water in Westchase?

Yes, when the rinse is done carefully. Rusty's says it rinses thoroughly so cleaner never reaches the pool water or the landscaping, and it calls an algae covered deck a slip and fall hazard. It suggests cleaning once a year, or every 9 months under heavy tree cover.

What is the white film on newer pavers?

Most often it is efflorescence, a powdery deposit of calcium salts. Unilock says it is cosmetic and does not weaken pavers, and that it may take 2 to 3 months, or up to a year, to fade. It has to be gone before sealer goes on, because sealing over it locks it in.

How long does paver cleaning take at a Westchase home?

Plan around drying time. Unilock says pavers may dry in a few hours in warm sun and need about a day in cool shade before sand and sealer go on. A Westchase paver company says most full jobs there take one to two days.

Time to wash the green and gray off your Westchase pavers?

Call or fill in the short form, and a contractor writes back inside 1 business day, usually sooner.

Call (656) 254-4152

Free, no obligation